Franklinbrew

Draft systems & serving

Draft Line Balancing Calculator

Find a starting length for your beer line.

Estimate beer line length from your serving pressure, tubing resistance and tap height. Then fine-tune with a cold test pour.

See the method & assumptions

Your setup

Measurement units
bar

Gauge pressure at the keg, already chosen to maintain your beer’s carbonation.

Nominal reference only. Check your tubing manufacturer’s specification.

bar/m

Editable. Use a pressure drop per unit length at the intended flow rate. Why this matters

m

Vertical difference, not hose length. Enter a negative value for a tap below the keg centre.

Additional system resistance
bar

Combined loss through other components at the same flow rate, if known. Default: zero; no automatic faucet allowance is subtracted. Do not count the hose twice.

Single line type · Conventional CO₂ draft system

Your result

Starting line length

Enter your setup

— m

An estimate to test on your equipment.

Where the pressure goes

Available for beer line
—
Used by elevation
—
Other known losses
—

Make the next pour count.

Leave some extra hose for adjustment. Chill the whole beer path, test with the faucet fully open, and shorten in small steps if the pour is too slow.

Keep serving pressure appropriate for carbonation. A warm faucet, dirty line or overcarbonated keg can still cause foam.

Behind the calculation

A simple balance.
Visible assumptions.

Every input has a job. Here is how it becomes a line length.

The equation

L = (P − G × H − A) / R

L
Calculated line length
P
Serving gauge pressure
G × H
Elevation allowance: 0.5 psi/ft × signed height (≈ 0.1131 bar/m)
A
Other known pressure losses
R
Line resistance per unit length

Why the tubing value matters

The two vinyl presets use nominal values of 3.00 and 0.85 psi/ft for 3/16″ and 1/4″ internal diameters. Actual resistance varies by product and flow. Use the manufacturer’s value at your intended flow; do not apply vinyl values to barrier tubing.

Height, flow and model limits

The 0.5 psi/ft elevation factor is a draught-industry convention; the manual also gives about 0.43 psi/ft for hydrostatic head. Measure from the keg centre. A lower tap increases the pressure available to the line.

Resistance values imply a flow condition. This model does not independently calculate flow or add an arbitrary “pressure at the faucet.” It assumes one tubing type and excludes pumps, mixed-gas design, nitro restrictors and multi-section long-draw design.

What if the calculated hose cannot reach?

A hose must reach the faucet without stretching or kinking. If the estimate is shorter than the physical route, review the tubing and system design. The calculator checks vertical reach; bends and horizontal distance need your own check.

When this tool asks you to review a result

Review prompts appear above 2 bar (≈ 29 psi) serving pressure, above 2 m (≈ 6.56 ft) of absolute height difference, or for a calculated line shorter than 0.30 m (≈ 0.98 ft) or longer than 6 m (≈ 19.69 ft). A separate prompt appears when less than 5% of the driving pressure remains for the line.

These are editorial prompts chosen for this home-draft tool. They are not manufacturer limits, safety ratings or a validated operating range. Values beyond them are still calculated when mathematically possible; equipment suitability requires its own specifications. Exactly at a threshold, that particular prompt is not shown.

If elevation and other losses exhaust the pressure, there is no positive line-length result. Values indistinguishable from zero at numerical precision receive the same treatment. Tiny positive results are displayed as “< 0.01” instead of a misleading zero.

Sources & review

Brewers Association · Draught Beer Quality Manual, 4th edition
Printed pp. 38–39: elevation convention and nominal tubing values.

Micro Matic · What is restriction?
Set pressure for carbonation, then balance the beer path.

Method reviewed 16 November 2026 · Version 1.1
Reference values are estimates, not a calibration of your tubing.

Before you cut the line

Check the specification

Confirm the actual tubing material, internal diameter and resistance. A nominal size alone is not enough.

Check the route

Allow for fittings, bends and a practical route inside the fridge. Keep the entire beer path cold.

Record a test pour

Note pressure, beer temperature, line length and the pour. Change one thing at a time.

Back to brewing calculators