Franklinbrew

Ingredients & measurements

Residual Alkalinity and Mash pH

Use the water report and the grist, not beer colour alone.

Understand the historical RA approximation, its units and why an actual mash-pH model and measurement are still needed.

Reviewed 17 November 2026 · Version 1.0

Residual alkalinity is a useful piece of brewing-water history and an approximate descriptor. It is not the pH of your water, a full mash-pH prediction or a direct recipe for adding acid.

Alkalinity, hardness and pH are different properties

Alkalinity describes acid-neutralising capacity. Calcium and magnesium contribute to hardness. Residual alkalinity combines alkalinity with an approximate allowance for hardness effects in brewing.

Water pH alone does not provide those quantities. A water report giving only pH is insufficient for a useful mash-water calculation. Similarly, a low RA value is not a laboratory measurement of the mash pH.

The mash also contains grain and other additions. Its acidity and buffering behaviour matter, so the same water can behave differently with a different grist.

Section references: Bru’n Water — Water Knowledge, including residual alkalinity.

“As CaCO₃” is not the elemental ion concentration

A report may express alkalinity or hardness in mg/L as CaCO₃, while listing calcium and magnesium in mg/L of the actual ions. Those columns cannot be inserted into a formula as if they were the same convention.

When reading a classical RA equation, confirm whether its calcium and magnesium terms mean elemental concentrations or equivalent hardness. Coefficients belong to that exact unit convention. We deliberately avoid presenting an unlabelled formula that invites a mixed-unit calculation.

Keep the original report alongside the entered data. A computed negative RA is a result of the approximation; it is not a physically negative bicarbonate concentration.

Section references: Bru’n Water — Water Knowledge, including residual alkalinity.

Similar-coloured grists can have different acidity

Finished-beer SRM is not a complete description of the grist’s acid-base behaviour. Different ingredients and proportions can produce a similar colour while contributing different acidity.

Consequently, a chart matching a single RA target to each colour should not replace a mash model using the actual grain bill and water. Colour remains useful for describing appearance; it does not become a complete water specification.

Also keep flavour-ion choices separate from pH correction. A desired sulfate or chloride profile does not automatically establish the required acid addition.

Section references: Bru’n Water — Why beer colour is an incomplete water guide.

Model the actual mash and measure the result

  1. Obtain a current report for the water actually being used, including alkalinity and relevant ions with units.
  2. Record source changes, dilution or treatment rather than assuming last year’s report remains exact.
  3. Enter the real grist and water volumes into a documented water tool, checking every input convention.
  4. Choose any additions using their actual composition or acid concentration. Do not use a universal mL-per-batch dose.
  5. Measure a suitably cooled mash sample with a calibrated meter and compare it with the intended target under the same measurement convention.
  6. Record the prediction, measurement and adjustments for the next comparable brew.

A target measured at room temperature must not be compared casually with a hot reading. Automatic temperature compensation does not make the chemical pH of hot and cooled samples identical.

Section references: Bru’n Water — Water Knowledge, including residual alkalinity · Bru’n Water — Getting started · Bru’n Water — Variable water quality.

Use an established model without hiding the gaps

Bru’n Water’s getting-started guide links the author’s documented workflow and tool. Read its water-knowledge material before entering numbers. A tool can only use the information supplied.

If alkalinity, water source or the product strength is unknown, resolve it before relying on a precise acid recommendation. If the measured mash differs, investigate the report, entries, meter and process rather than treating the estimate as a measurement.

The former /tools/rac2.html addressed residual alkalinity. This page explains that subject and openly changes the function to reference guidance; it does not pretend the old calculator is operating here.

Sources & scope

References and review

Definitions and limitations were checked against the technical author’s water documentation. No acid dose, exact mash-pH prediction or universal colour-to-RA target is supplied. The linked external tool is maintained separately from Franklinbrew.

  1. Bru’n Water — Water Knowledge, including residual alkalinity
  2. Bru’n Water — Why beer colour is an incomplete water guide
  3. Bru’n Water — Getting started
  4. Bru’n Water — Variable water quality

Franklinbrew · Independently written reference · Version 1.0 · Reviewed 17 November 2026.