Franklinbrew

Equipment & reference

Walk-In Coolers for Homebrewers

Size the room around the load, the moisture and the way you will use it.

Put a historical DIY cooler in context and plan a modern cold space without copying old wiring or incomplete heat-load estimates.

Reviewed 17 November 2026 · Version 1.0

A walk-in gives several vessels a shared cold environment. It also introduces an envelope, door, moisture load and refrigeration duty that a small kegerator does not have. More volume is not automatically the best solution.

An instructive build, with reported icing problems

The recovered Franklinbrew article described an insulated enclosure approximately 8 ft wide, 4 ft deep and 6 ft high, cooled with an old window air conditioner. Its intended uses included lager fermentation, keg storage and grain storage.

The author reported coil icing and later fan and control changes. Those reports are valuable evidence about the build’s development; they are not proof that an arbitrary room and air conditioner form a dependable cold-storage system.

The old page includes electrical modifications and a conduction-based heat-loss calculation. We do not reproduce its wiring or treat that calculation as a complete current refrigeration specification. Historic cost figures are not current prices.

Section references: Historical Franklinbrew walk-in — Wayback capture, 18 June 2007.

A shared room means a shared temperature

Define the target first: fermenting one temperature group, conditioning beer, or storing connected serving kegs. Those uses may not share the same ideal setpoint. A room at one temperature is not independent temperature control for every vessel.

Compare the need with smaller alternatives: a chamber, several controlled fridges or a compact serving cabinet. Include vessel handling, floor loading, service access and the ability to clean the space.

Grain storage also needs suitable dryness and protection. A cool but damp room should not be assumed suitable merely because an old project listed grain among its possible contents.

The envelope includes the floor, ceiling and joints

Plan a continuous insulated and sealed envelope, including door seals, joints and service penetrations. Moist air entering or passing into cold construction can create condensation problems. Moisture and vapour control need to suit the actual wall assembly and climate.

The CoolBot insulation guide is a useful manufacturer example of whole-room planning; its recommendations belong to its application, not a universal building specification. Have material, vapour-control and fire requirements checked for the intended location.

Include a cleanable interior and a plan for condensate and spills. Do not hide an unresolved drainage or moisture problem behind a larger cooling unit.

Section references: CoolBot — Insulating the room.

Room dimensions are only part of the load

Refrigeration must handle more than heat conducted through the walls. Warm beer entering the room, door openings, air exchange and equipment operating inside can materially change the duty.

Write those use conditions down before asking for a size. Use manufacturer sizing guidance and confirmed equipment compatibility, including the intended operating temperature. A normal room air conditioner is not automatically suitable for a beer-cooler target.

A controller product designed for compatible cooling equipment is a distinct route from bypassing appliance controls. Do not repeat historical sensor, wiring or anti-icing modifications as a current instruction.

Section references: CoolBot — Air conditioner sizing and compatibility · CoolBot — AC care guide.

Judge the room under the load it will actually see

Keep a commissioning record

  • Target temperature, room conditions and representative load.
  • Measured temperature at useful positions, not only one wall sensor.
  • Recovery after typical door openings and a warm load.
  • Coil icing, air circulation and condensate behaviour.
  • Door operation, access and any applicable occupancy provisions.
  • Measured energy consumption over representative operation.

Use the equipment instructions for abnormal operation. Persistent icing is a fault to resolve, not a reason to remove protection or adopt an unverified control modification.

For connected serving kegs, the cold room is only part of the draft design. A beer line leaving it still needs a suitable cooling and dispensing plan; our direct-draw tools do not design a remote run.

Sources & scope

References and review

Historical description was verified in the recovered primary text. Archive access is variable. Modern manufacturer guidance informs the planning questions; no refrigeration size, construction detail, moisture design or operating cost has been approved for a particular location.

  1. Historical Franklinbrew walk-in — Wayback capture, 18 June 2007
  2. CoolBot — Insulating the room
  3. CoolBot — Air conditioner sizing and compatibility
  4. CoolBot — AC care guide

Franklinbrew · Independently written reference · Version 1.0 · Reviewed 17 November 2026.