Franklinbrew

Draft systems & serving

Carbonation: Temperature, Pressure and Time

An equilibrium target tells you where the beer is heading, not when it will arrive.

Understand volumes of CO₂, gauge pressure, temperature changes and the limits of a carbonation calculator.

Reviewed 17 November 2026 · Version 1.0

Three statements can all be true: the regulator is set correctly, the keg is cold, and the beer has not yet reached its intended carbonation. Pressure and temperature define a target equilibrium; the route there takes time.

Volumes describe dissolved CO₂

A carbonation value in volumes compares the amount of gas, expressed at a stated reference condition, with the volume of beer. It is not the number of keg headspaces filled with gas or the additional amount you must inject.

The reference convention used by our tool is gas at 0°C and 760 mmHg. Published charts can also assume a particular beer composition. Alcohol and dissolved extract vary between beers; an empirical planning equation is not a laboratory measurement of every recipe.

Use the brewer’s target when available. Choosing a value because it is a calculator default does not establish that it suits the beer.

Section references: Zahm & Nagel — CO₂ in beer chart · Brewers Association — carbonation table, appendix B.

Colder beer can hold more CO₂ at the same pressure

For the same target carbonation, colder beer needs a lower equilibrium CO₂ pressure than warmer beer. Conversely, keeping the same pressure while warming the beer changes the equilibrium carbonation it can sustain.

Measure liquid temperature after conditions stabilise. A refrigerator setting is not a substitute. Warming in a line or tower can also change conditions between keg and faucet, even if the keg itself is cold.

One stated set of inputs

At 4°C / 39.2°F, 2.5 volumes and 1013.25 hPa local atmospheric pressure, our polynomial returns approximately 0.82 bar / 11.86 psi gauge. It is an example for those conditions, not a universal serving pressure.

Section references: Brewers Association — carbonation table, appendix B · GW Kent — Carbonation Calculator: formulas and assumptions.

The gauge reads relative to the air around it

Absolute pressure equals gauge pressure plus local atmospheric pressure. To maintain the same absolute CO₂ pressure at a lower local atmospheric pressure, the required gauge reading rises.

Our correction is Plocal,gauge = Psea-level,gauge + 1.01325 bar − Patmosphere. Use actual local atmospheric pressure, not a weather report corrected to sea level. An altitude estimate and a corrected weather reading are not interchangeable inputs.

A negative calculated gauge pressure is reported as a vacuum requirement, not silently changed to zero or recommended as a regulator setting. Hardware suitability is a separate question.

The headspace changes before the whole beer does

Gas must move into or out of the liquid before the beer reaches a new equilibrium. Temperature, contact area, mixing, starting carbonation and the chosen equipment affect that process. An equilibrium equation contains no time variable and cannot promise “ready in 24 hours”.

For an initial setup, follow a documented holding-pressure method for your equipment, allow stable temperature and assess the beer over time. A temporarily higher pressure changes the driving force, but also makes overshoot possible. A generic high-pressure shaking schedule would hide the variables that matter.

Commercially filled beer may already be at its intended carbonation. The job is often to preserve that condition while dispensing, rather than carbonate it again.

Read the result status as well as the number

The tool supports 0–30°C, 1–4 volumes and 0.5–1.1 bar absolute atmosphere. These are implementation boundaries, not source-proven validity or equipment-safety limits. Its independent chart comparison covers 33–42°F and 2.1–3.1 volumes; outside that rectangle, supported results are marked as extrapolation.

Across 110 published reference points, the largest difference from the polynomial was about 0.369 psi / 0.0254 bar. That observed comparison is not a universal error bound for every beer or temperature.

If a calculated state does not produce a useful pour, preserve the distinction between carbonation and dispensing. Check line resistance and the cold path. Foam alone is not a measurement of dissolved CO₂.

Section references: Brewers Association — carbonation table, appendix B · GW Kent — Carbonation Calculator: formulas and assumptions.

Sources & scope

References and review

The numerical example, model scope and comparison statistics were checked against the local model and its recorded independent reference fixture. No carbonation-time experiment or measurement of an actual keg has been performed.

  1. Zahm & Nagel — CO₂ in beer chart
  2. Brewers Association — carbonation table, appendix B
  3. GW Kent — Carbonation Calculator: formulas and assumptions

Franklinbrew · Independently written reference · Version 1.0 · Reviewed 17 November 2026.