Franklinbrew

Draft systems & serving

Choosing Beer Line

Buy a tubing specification, not just a diameter.

Compare ID, OD, material, resistance, fitting compatibility, cleanability and route length before replacing beer line.

Reviewed 17 November 2026 · Version 1.0

A tube can fit a connector and still be the wrong choice for the beer path. Capacity, resistance, flexibility and connection dimensions are separate properties to verify.

Read both diameters before ordering

Inside diameter (ID) is the open bore through which beer travels. Outside diameter (OD) includes the wall. A quoted “4 mm line” is incomplete unless you know which dimension it names.

A push-fit connector commonly specifies tube OD and approved tube type; a hose-barb joint has its own compatible hose and retention requirements. Follow the actual fitting documentation rather than assuming every tube with the same ID will connect.

A useful purchase note

  • Manufacturer and tubing product code.
  • ID and OD, with units and tolerances if supplied.
  • Approved beverage use, temperature and pressure range.
  • Compatible fittings and installation method.
  • Resistance or flow data and the conditions at which they apply.

Material affects more than flexibility

Flexible vinyl and multilayer barrier tubing are broad families, not single specifications. A barrier layer can reduce gas permeation, but that does not make the product sterile or remove the need for cleaning.

Look at the exact product’s resistance to gas transfer, cleaning chemicals, repeated bending and the temperatures in your system. Supplier product descriptions are useful for those claims; they are not a reason to transfer one product’s numerical resistance to another.

Ask for the minimum bend radius and approved installation method where a tight cabinet route makes them relevant. Avoid kinks and stress at the connector. A tube that reaches only when stretched does not provide a serviceable route.

Section references: Micro Matic — Barriermaster product specification · Micro Matic — Clear barrier vinyl hose.

Two tubes can hold the same volume and pour differently

Capacity follows geometry: for a straight uniform circular bore, V = π × ID² × L / 4. Resistance describes pressure loss under flow. It also depends on material and operating conditions, so geometry alone does not provide a dependable nominal psi-per-foot value.

A 4 mm ID, 2 m line holds approximately 25.13 mL. Doubling length doubles that capacity. Doubling ID quadruples it. None of those capacity statements supplies a resistance coefficient or a predicted pour time.

Use the line-volume tool for capacity and the balancing tool with appropriate supplier resistance data for a starting length. Include separately specified component losses only on a consistent basis.

Section references: Micro Matic — What is restriction?.

A calculated length still has to fit the cabinet

Measure the real path, including bends, service access and the connected keg. Keep beer-contact tubing cold throughout the run. A neatly coiled excess length can add resistance, but an uncooled section can introduce another problem.

If the calculated length is shorter than the route, pause the selection and review tubing and layout. Do not claim success by cutting a line that cannot connect the keg to the faucet. If you need a multi-section or remote system, the simple one-line calculator is not a complete design.

Changing tubing may also change fittings. Verify the entire replacement assembly rather than assuming the old disconnect outlet, barb, seal or push-fit adapter remains suitable.

Choose a line you can maintain

Confirm the tubing manufacturer’s permitted cleaners, concentrations, temperatures and methods. Clean the line and connected components as a system; a new tube does not clean a dirty faucet.

Inspect during service. Replace tubing that is damaged, kinked, incompatible with the intended process or impossible to restore using the approved cleaning method. Colour alone does not establish cleanliness or prove that a line is ruined.

Keep the product specification and installed length with your setup record. When the pour changes after a replacement, those records help distinguish a different resistance from a temperature, connection or cleaning issue.

Sources & scope

References and review

Product examples illustrate why tubing families need individual specifications. No generic pressure rating, service life or resistance is inferred from diameter. The capacity example is an independent geometric calculation.

  1. Micro Matic — Barriermaster product specification
  2. Micro Matic — Clear barrier vinyl hose
  3. Micro Matic — What is restriction?

Franklinbrew · Independently written reference · Version 1.0 · Reviewed 17 November 2026.